We have come across the article about How to Install a Bathtub down the page on the web and think it made perfect sense to share it with you in this article.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bath tub with a brand-new one is additionally a moderately difficult task. If the old tub is readily easily accessible, the project can relocate immediately; if you have to open up a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This post will certainly assist you mount a new tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not require to alter the setup of your previous water supply pipelines.
Your devices and product list should make up the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the limited access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Secure the faucet in position with the maker supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bath tub up until the level checks out level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water supply as well as examine all joints and new pipework for leakages and also tighten them if required. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait till the bathtub has been utilized at the very least once as this will settle it right into its last placement.
Preparing for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break an inflexible seal, creating the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealer can split fairly very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly readily available on the market. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading about How to Install a Bathtub Yourself? Make a short review further down. We'd be interested to know your views about this posting. We are looking forward that you visit us again before long. Do you know about another individual who is occupied with the subject? Please feel free to share it. Thank you for your time. Don't hesitate to stop by our blog back soon.
Schedule Now!